Movincool GX484560-2320 User Manual download pdf

1. Inventory

After unpacking, please check to make sure you have the correct part number of the

switch assembly. If the switch assembly has incorrect part number or appear damaged,

please contact your MovinCool reseller for replacement (See Fig.1). Please keep this

installation manual with the operation manual for future reference.

INSTALLATION MANUAL

For Classic Plus 14 - Serial Number: 1200XXXX140 to 0307XXXX140

Switch Assembly (Part No. GX484560-2320)

Switch Assembly

Fig. 2

Fig. 1

2. Installation of Switch Assembly

WARNING: Disconnect power supply from the unit before performing any

service. Beware that some residual voltages may remain in the

unit immediately after the power is disconnected.

2-1. Connect the following connectors to the switch assembly (See Fig. 2):

A. J201 (10-pin) Wire Harness, relay board to the switch assembly.

B. J101 (2-pin) Room Temperature Thermistor.

C. J102 (2-pin) Freeze Protection Thermistor.

D. J103 (2-pin) Drain Tank Switch.

< NOTE >

• Connector J104, J106, and J108 are not used.

Classic Plus 14

Manual P/N: GX484007-3710 First Issue: June 2012

4. Self-Diagnostic Codes of Switch Assembly

LCD Display Description Condition Reset/Remedy

Drain tank is full. When the drain tank is filled

with drain water.

(“TANK FL” LED flashes.)

1)Drain away.

(LCD indicates “TANK”)

Condensate pump

problem

When (optional) condensate

pump is damaged or broken.

1)Fix the condensate pump.

2)Reset the system.

To RESET: Press ON/OFF

and HI/LO buttons on the

control box simultaneously

for 5 seconds.

2)Press ON/OFF button.

Defect (short or

open) of room

thermistor

When room thermistor

(connecting to J101) becomes

short or open.

Disconnect and reconnect

the room thermistor.

If it does not work, then

change it.

Defect (short or

open of freeze

protection

thermistor

When freeze protection

thermistor (connecting to

J102) becomes short or open.

Disconnect and reconnect

the freeze protection

thermistor. If it does not work,

then change it.



SET TEMP

COOL

FAN

SET TEMP

COOL

FAN

SET TEMP

COOL

FAN

SET TEMP

COOL

FAN

SET TEMP

COOL

FAN

3-4. Operating in FAN ONLY Mode

1. The unit can also be operated in FAN ONLY mode by pressing FAN HI/LO

button (LCD indicates “FAN HI/LO” and “COOL OFF”).

2. The unit can then be turned off by pressing the FAN HI/LO button until fan

turns off (FAN ONLY mode speed sequences are HI > LO > OFF).

3-5. Changing from FAN ONLY Mode to COOL Mode

The COOL mode can be activated while the unit is operating in FAN ONLY mode.

To do this, simply press the COOL ON/OFF button (LCD indicates “COOL ON”).

Note: The FAN ONLY mode does not operate after the COOL mode has been

activated. The unit can only be turned off by pressing the COOL ON/OFF button.

3. Operation of Switch Assembly (cont.)

1 2

INSTALLATION MANUAL 1
Classic Plus 14 2

Summary of Contents

Page 1 - INSTALLATION MANUAL

1. InventoryAfter unpacking, please check to make sure you have the correct part number of theswitch assembly. If the switch assembly has incorrect pa

Page 2 - Classic Plus 14

33. Operation of Switch Assembly (cont.)3-2. LCD indicators (See Fig. 6) Note: ROOM TEMP display range is from 16 °F (-9 °C) to 109 °F (42 °C). When

Comments to this Manuals

No comments

Movincool GX484560-2320 User Manual

Browse online or download User Manual for Hardware Movincool GX484560-2320. MovinCool GX484560-2320 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Movincool GX484560-2320